Masterbuilder Gouts come in two varieties: Cementitious and Epoxy type.
Cementitious Grouts:
General construction, natural aggregate, nonshrink grout is a non-catalyzed, multi-purpose construction grout containing mineral aggregate. This Portland cement-based product is designed to meet all of the performance requirements of the Corps of Engineers Specification CRD-C621-89 at a flowable or plastic consistency.
Recommended for:
-Normal loads for columns and baseplates
-Anchoring bolts, reinforcing bars and roadway dowels
-Bedding grout for precast panels
-Repairing of cavities resulting from ineffective concrete consolidation
-Caulking, underpinning foundations and pressure grouting of -slabs needing alignment
-General construction applications
-Dry pack applicationsFeatures:
-Free of inorganic accelerators, including chlorides or other salts detrimental to reinforcing steel
-Colour similar to concrete after curing
-Can be extended with clean, well-graded coarse aggregate to fill large voids without additional mix water.
-Hardens free of bleeding when placed at a plastic or flowable consistency and when ambient temperature are 500 F (100 C) and aboveAPPLICATIONS:
Consult the CONSTRCTION GROUT product bag for details on the installation of CONSTRUCTION GROUT.
PACKAGING:
50 lb (22.7 kg) moisture-resistance bags
ESTIMATION:
One 50 lb (22.7 kg) bag of CONSTRUCTION GROUT mixed with 1.15 gallons (4.35 litres) of water provides approximately 0.45 ft3 (0.013 m3 ) of mixed grout.
TECHNICAL DATA:
Typical Mixed Grout Data (Flowable Mix) Approximate Water: 1.15 gallons(4.34 litres) Flow: 5 drops (ASTM C230) 126% to 145% At a constant percent of water, consistency will vary with temperature. Final sat takes place in approximately 8 hours at a flowable consistency, 70* F (21*C).
Initial Set @ 70* F 6 hours
Final Set @ 70* F 6 hours140% flow on flow table, ASTM C 230, 5 drops in 3 seconds.
100% flow on flow table, ASTM C 230, 5 drops in 3 seconds.
40% flow on flow table, ASTM C 230, 5 drops in 3 seconds.
MASTERFLOW 555 Fluid, nonshrink, natural aggregate grout is a fluid, nonshrink, natural aggregate grout. It is ideally suited for grouting machines or plates requiring optimum load-bearing support. MASTERFLOW 555 grout meets the requirements of ASTM C 1107 and the Army Corps of Engineers CRD C 621, Grades B and C at a fluid consistency.
Recommended for:
Nonshrink grouting of: - Machinery and equipment - baseplates and soleplates - Precast wall panels, beams and columns, curtain walls, concrete systems, and other structural and on structural building members. - Anchor bolts, reinforcing bars and dowel rods
Repairing concrete, including grouting voids, rock pockets and large cracks q Application requiring high one-day and later-age compressive strengths q Applications requiring nonshrink grout to achieve maximum bearing for optimum load tansfer.
Features:
Meets ASTM C 1107 and CRD C 621, Grades B and C requirements at a fluid (30 second flow) consistency over a temperature range of 50 to 90 degree F (10 to 32 degrees C).
Fluid consistency and good working time provides excellent handling and placement capabilities
Can be installed over a temperature range of 50 to 90 degree F (10 to 32 degrees C) q Hardens free of bleeding, segregation, or settlement shrinkage ensuring optimum performance in the hardened state.
Free of inorganic accelerators, including chlorides or other salts that are detrimental to reinforcing steel.
Packaging:
50 lb (22.7 kg) moisture-resistance bags.
Estimation:
One 50 lb (22.7 kg) bag of MASTERFLOW 555 grout mixed with approximately 8.3 lb (3.8 kg) or 1.0 U.S. gal (3.8 l) of water yields approximately 0.42 cubic ft (0.012 cubic meters) of grout Note: The water requirement may vary due to mixing efficiency and other variables.
Epoxy Grouts
MASTERFLOW 648 CP PLUS High strength, high temperature, high flow epoxy grout
MASTERFLOW 648 CP PLUS grout represents the continued evolution of Master Builders grout technology building on over fur decades of continuous improvement in polymer and aggregate technology.
MASTERFLOW 648 CP PLUS grout combines high temperature performance and crack resistance with outstanding flow characteristics and versatility of fill rates.
RECOMMENDED FOR:
Precision alignment of machinery, compressors and prime movers in the gas transmission and other industries
Foundations under crusher ball mills, slab tables and other equipment in the steel industry
The pulp and paper, chemical processing, mining and power industries for a wide variety of applications
Applications requiring fast turnaround with high early and seven day compressive strengthsFEATURES/BENEFITS:
High early and seven day strengths
Superior physical properties at high temperatures
Excellent bearing area and flow
Variable fill ratio for the optimum mix of flowability, bearing area and economics on a project by project basis
Good chemical resistancePACKAGING:
MASTERFLOW 648 CP PLUS grout is available in two unitized package sizes for convenience. Due to installation variables etc., it is best to order an additional 10 to 20 % as a safety precaution.
216 lb Full Unit (1.73 ft3, 0.05 m3)
-Grout Liquid one 20.2 lb pail (10.06 kg)
-Hardener one 7.6 lb bottle (3.4 kg)
-Grout Aggregate one 47 lb bag (21.3 kg)(54.4 lb unit is shipped in a U.S. gal pail over-pack)
Site
design and all content © 2002 Harricrete Ltd., Trinidad & Tobago, W.I.
Company email addresses
& full contact information here.
Site by Webworks.
Legal Notice
